BEFORE YOU START:
1. Prep the surface with a clean microfiber cloth and isopropyl alcohol or any surface cleaner, avoiding anything ammonia-based. Allow time to dry.
2. If you have any ceramic, wax, or coating on your car, we recommend removing it – usually by polishing it off, either by machine or by hand.
3. Ensure the surface temperature is at least 70-80 degrees Fahrenheit (the decal will not adhere properly otherwise). Out of direct sunlight.
4. Finish with a dry microfiber cloth to remove any lint or dust.
SURFACES: Transfer decals work best on smooth, non-porous surfaces, like metal, ceramic, glass, windows, and some painted surfaces. Surfaces like oily and textured plastics pose diffuculty applying the decal
STEPS:
1. Press the transfer tape down using your fingernail or a hard edge. You can also flip it over and apply more pressure.
2. Pick a corner and gently peel the transfer tape up off the backing paper. If you notice part of the decal not being picked up, lay the transfer tape back down and press firmly around the entire decal.
3. Carefully apply the decal to the surface, starting with one side and working your way over, forcing all the air out. Use a credit card, squeegee, or your hand to help smooth the decal onto the surface.
4. Remove the transfer tape by peeling it away at a 45-degree angle. If you notice part of the decal not adhering to the surface, gently place the transfer tape back down and press firmly.
ATTENTION: If your decal is having trouble adhering to the surface, place it back down and press firmly over every spot. Allow the decal to sit with the transfer tape on for 24 hours. You can also use a heat gun or hair dryer to improve adhesion, but be sure to let the decal cool and cure before removing the transfer tape.
If your decal is having issues adhering to the surface. After you followed every step and tried both tips. Please provide photo evidence for a replacement.
WATER APPLICATION: If your decal has a paper transfer tape (not plastic with red lines) or metallic vinyl, you can use water to apply the decal.
1. Lightly spray the surface and back of the decal, ensuring it’s covered but not dripping.
2. Go back to number 3.
WATER TIP: Spray the backing paper with water to loosen the transfer tape.
REMOVING: You must wait for all the water to dry out before removing (24 hours)
BUBBLES: If you get bubbles, don’t worry; they will work themselves out over time. Around 90% should disappear after a week. Larger bubbles might take longer.
AFTER: Don’t touch for at least 48 hours. Don’t use rubbing alcohol on the vinyl. Don’t wipe over the decal at any time; if you need to clean, dab and wipe away from the edge very gently. Over time, if your decal has an edge that starts lifting, use a heat source and firmly press down on the edge.
REMOVAL: Removing decals can be a time-consuming task depending on how complex your design is, what type of vinyl you have, and how old your decal is. You can either use a scraper, like a plastic razor blade, or just your fingernails. Using heat, such as from a hair dryer, can soften the vinyl and adhesive, speeding up the process. If, by chance, you encounter glue residue, use isopropyl alcohol or goof off
STEPS:
1. Measure and mark your placement on the glass.
2. Position the banner and tape it down on all four sides.
3. Starting from one side, lift the transfer tape with the vinyl off the backing paper. If part of the decal doesn’t lift, lay the transfer tape back down and press firmly over the area.
4. Use sharp scissors to carefully cut away the exposed backing paper. (Warning: If the paper tears, small particles can stick to the vinyl.)
5. Using your hand or a squeegee, apply the decal slowly from one side to the other, pressing out all air bubbles as you go.
6. Peel off the remaining backing paper and repeat the application process until the entire decal is applied.
7. Allow 10–20 minutes for the vinyl to adhere to the glass before removing the transfer tape.
8. Remove the transfer tape by peeling it back slowly at a 45° angle. If any part of the decal lifts, place the tape back down and press firmly before peeling again.
ATTENTION: If your decal is having trouble adhering to the surface, place it back down and press firmly over every spot. Allow the decal to sit with the transfer tape on for 24 hours. You can also use a heat gun or hair dryer to improve adhesion, but be sure to let the decal cool and cure before removing the transfer tape.
If your decal is having issues adhering to the surface. After you followed every step and tried both tips. Please provide photo evidence for a replacement.
WATER APPLICATION: If your decal has a paper transfer tape and not metallic, you can use water to apply the decal.
1. Lightly spray the surface and back of the decal, ensuring it’s covered but not dripping.
2. Go back to number 3.
WATER TIP: Spray the backing paper with water to loosen the transfer tape.
REMOVING: You must wait for all the water to dry out before removing (24 hours)
BUBBLES: If you get bubbles, don’t worry; they will work themselves out over time. Around 90% should disappear after a week. Larger bubbles might take longer.
AFTER: Don’t touch for at least 48 hours. Don’t use rubbing alcohol on the vinyl. Don’t wipe over the decal at any time; if you need to clean, dab and wipe away from the edge very gently. Over time, if your decal has an edge that starts lifting, use a heat source and firmly press down on the edge.
REMOVAL: Removing decals can be a time-consuming task depending on how complex your design is, what type of vinyl you have, and how old your decal is. You can either use a scraper, like a plastic razor blade, or just your fingernails. Using heat, such as from a hair dryer, can soften the vinyl and adhesive, speeding up the process. If, by chance, you encounter glue residue, use isopropyl alcohol or goof off
BOTTLE SLEEVE
STEPS:
1. Look to see if your bottle has a seam line. If not, precisely mark a spot above and below your starting location.
2. Spray both your vinyl and bottle generously with water. (This will make it easier to adjust in case you place it incorrectly.) Then carefully place your vinyl down, making it as straight as possible.
3. Slowly and gently wrap your vinyl around the bottle, making sure there are no bubbles or creases.
4. If your vinyl lines up with your starting point, good job! If not, start again and spray your vinyl once more. WARNING: If you accidentally place your vinyl on top of the beginning edge, you can try to carefully remove it, but it may be unmovable without stretching. This vinyl does not stretch.
PLEASE LET THE BOTTLE SIT OUT AND DRY BEFORE USING.
BOTTLE LABEL
STEPS:
1. Place your bottle on a level surface and make sure you’re standing perpendicular to it.
2. If you want to be precise, you can use a ruler to mark points for placement. However, I’ve noticed that even larger errors are hardly noticeable once the bottle is in use.
3. Place the label on as straight as you can. If you mess up, there’s no going back, just finish applying it the way it is.
4. If you’re placing it on a bottle sleeve, you can usually remove it right away if needed. But if it starts to lift, just leave it overnight and try removing it the next day.
WARNING: If you’re placing this on a plastic bottle surface, you must wait at least 24–48 hours before removing the transfer layer. It will stick, I guarantee, but some bottles take longer for the vinyl to fully adhere. It may take multiple days. Do not worry, if you start to lift it and it comes up, just wait another day. You can use gentle heat to speed up the process, but it will still need time to set.
BEFORE YOU START:
1. Make sure the paint is properly corrected, remove scratches, paint chips, waxes, sealants, and debris. If your paint has heavy scratches or light fading, improve it as much as possible before applying PPF. Don’t just clean the area you’re applying it to, clean everything around it. Ideally, wash the entire car before starting the process.
2. Fill a spray bottle with water and add a single drop of shampoo. Baby shampoo is typically used, but any mild shampoo with low detergents and no oils, waxes, or scents will work. It’s recommended to wear clean gloves during installation. A squeegee isn’t usually necessary since these kits are small and precisely cut.
GENERAL PPF
STEPS:
1. Spray the entire surface generously, along with your gloves. As you peel the PPF from the backing paper, spray the adhesive side as it’s coming off. Then, place the film in its general position on the panel.
2. Work from left to right, gently pressing out all water and air bubbles as you go.
3. If you notice bubbles or debris, carefully lift a corner while spraying slip solution underneath, then reapply and smooth it down again.
4. Blot away any remaining surface moisture with a clean microfiber towel, and let the car sit out in the sun (or in a warm area) to help the film bond properly.
5. For kits that involve going around a curve or edge, like the door handle or the trunk area. You will need to use heat.
6. Heat Application: Use a hairdryer or heat gun to gently warm the surrounding area. Work around lifted edges until they tack into place, ensuring all edges are securely sealed. Note that drying time may increase if water was used in the application, so adjust heating time accordingly.
DOOR EDGE/SIDE SCOOP EDGE
STEPS:
1. KEEP SURFACE DRY: Do not wet the car surface or the PPF, as moisture prevents proper adhesion.
2. Start at the top of the door / or side scoop. Peel back just enough of the PPF’s backing to tack the strip onto the surface.
3. Hold the backing paper in your left hand and the PPF strip in your right. Pull the film outward, away from the car, and angle it downward to align with the edge. Keep the line as straight as possible in one smooth, fluid motion. Avoid using your hands to press it down, as this can cause uneven edges. If the film starts to veer off, lift it and realign.
4. Once you reach the bottom, trim any excess PPF before final placement.
5. To place the remaining PPF, work it over the edge in one continuous motion, moving from right to left or left to right. Avoid pressing the entire top down fully to prevent creases. Apply a small area with each pass for a smooth, crease-free finish. Creases can ruin the application, so maintain steady control and avoid rushing.
STEPS:
1. After prepping the window, thoroughly wet the entire surface with water to aid in positioning the vinyl.
2. Remove the flag from the transfer paper and soak it with water to make it easier to handle and position.
3. Place the wet vinyl flag on the window and slide it into position, using the bottom seal and vertical edge as guides, prioritizing a parallel bottom edge over the vertical edges for best results.
4. Squeegee the vinyl to remove water and air bubbles, pressing it firmly onto the window for secure adhesion.
5. Allow the transfer paper to dry fully, waiting 24 hours to ensure the vinyl adheres completely and won’t lift when removing the transfer tape.
STEPS:
1. Make sure you grab the correct side, labeled on the back.
2. find the middle and start at the top, pressing it down until you get to the bottom.
3. start on one side, pressing it down in small sections, going all the way up and all the way down. until you get to the back edge. same thing on the other side
4. if you overstretched it, and have axcess on the back edge. take a new razor blade and gently trim off the hanging piece. *fix that wordring
ROUSH: if you have a roush you will need to remove teh grille before begining
ASPECT GRILLE: you will not need to remove anything
If you mess it up, dont worry about it, being so low and under a ledge, small errors are unnoticable.
BEFORE YOU START: If you have a metallic or custom color vinyl with air channels, you cannot use water. Standard colors, gloss, matte, and chrome can be used with water.
STEPS:
1. Spray the surface lightly with water, avoiding drenching it.
2. Take your first letter and lightly spray the back with water.
3. Slide the letter into position, ensuring it’s correctly placed before pressing it down.
OUTLINE: If you have an outline, it is much harder, so take your time.
STEPS
1. Take the large ring and place it
1. Remove the three push pins securing the bumper in place.
2. Attach three pieces of duct tape to the back of the bumper.
3. Slide the bumper at an angle into the recess on the impact foam, ensuring it fits directly in.
4. Press down on the taped areas to secure them and reinstall the three push pins.
BEFORE YOU START: All of our vinyl for stripes can be used with water. We do not use air release vinyl, as we found it easier to pick up corners with standard vinyl compared to calendared vinyl.
STEPS:
1. Use tape to position the vinyl stripe in place, just like a windshield banner, placing four pieces of tape, one on each side.
2. Once the stripe is lined up, pull back one side, remove the backing paper, and cut it with sharp scissors, avoiding ripping it.
3. Use your hand, a squeegee, or a hard edge to slowly press the stripe down evenly, ensuring all air bubbles are removed.
4. Pick up the remaining sides and smooth them down, just like the front.
5. Repeat the same process for all pieces.
POSITIONING: I like to keep the stripe 1/4 inch from the top edge, but this is a matter of preference.
STEPS:
1. Take the light tint vinyl and remove the backing paper.
2. Place the vinyl in the direct center, aligning it as best as possible.
3. Smooth the vinyl out toward the edges to ensure even application.
4. Use a heat gun to slowly heat the edges, working all around to keep it smooth and secure.
TOP
1. After removing the top grille, wipe the surrounding surface to remove any grime or dirt.
2. Place the grille on the specific side, grab the wooden rod and place it on the opposite side, then use two zip ties to fish through the grille and around the wooden rod, tightening just enough to secure without pushing the filler panel away from the grille, ensuring the grille’s edge aligns with the panel’s edge.
3. Apply adhesive all around the outside of the grille, smoothing it in to form a strong bond, noting that a gap on the driver’s side grille is intentional for the hood latch.
4. Leave the grille upside down for at least 24 hours to set.
BOTTOM
1. After removing the bumper, wipe the surrounding surface to remove any grime or dirt.
2. Place the grille on, using four zip ties tightened around the two bars connecting the top of the bumper to the bottom, with no need for rods.
3. Next, place two zip tie plates along the top of the grille and two along the bottom.
4. Apply adhesive around each plate, as the 3M adhesive alone is not strong enough, ensuring they are glued down securely.
5. Wait 24 hours, then tighten the zip ties until snug without over-tightening, cut off the tails, and remove the supporting zip ties on the bars.
SIDE SKIRT
STEPS:
1. Jack up the car and place jack stands, ensuring there’s enough clearance to get a drill underneath, and if the pinch flange is bent, pushing the skirt out, straighten it before installation to avoid a poor appearance, though this is optional.
2. Place a jack directly in the center of the skirt, adjusting it to position the skirt in the general area, then start from one side, lining it up with the back edge, while another person lines up the opposite side, jacking it up slightly more to press the skirt against the rocker.
3. Use a sharpie to mark the holes for drilling, though you can drill right away, marking first is recommended for accuracy.
4. Take a small drill bit and make pilot holes at each end to prevent the skirt from walking outwards, ensuring alignment before drilling the middle holes.
5. Finish drilling and screwing the skirt to the car, then apply a back-to-black product to make it shine.
POSITIONING: For GT skirts, you have more playroom, but for Cobra skirts, ensure you do not cross the bottom line, as it will be visible from the outside if misaligned.
DRILLING: Start at each end to avoid the skirt walking outwards.
REAR BUMPER
Before you start: make sure you remove the pins and hose clip on the bottom
1. Line up the front with the metal edge on the backside, line up the rear with the nearest edge next to the exhaust cut out.
2. use clamps, vise grips, to hold the skirt in the position you want it. and mark the two holes
3. You will be drilling trough metal, so take your time.
4. once you completed drilling, place your two bolts in and tighten them down snug.
5. Finish off with a nice back to black to make it shine.
Welcome to our installation guide page, where you’ll find step-by-step instructions for applying our vinyl transfer decals, car banners, stickers, and other products. This guide includes both video and text tutorials to walk you through each step with ease. You’ll also learn helpful tips for dry and wet application methods, surface preparation, and how to achieve a clean, bubble-free finish on glass, paint, plastic, and more.
Aspect USA is not liable for any errors occurring during the application and installation of our products. Customers are solely responsible for adhering to our application instructions and guidelines. We do not offer replacements for decals damaged due to scratching, mangling, wrinkling, ripping, tearing, or any other form of damage during installation.